ShaftDesigner 1.9.24
- New feature: flanged coupling with different flanges diameters
- New feature: the single shaft element may specify different from shaft material
- New feature: report 'page view' mode
- New feature: half coupling material added
- New feature: TVC nodes and elements may be removed from analysis in their properties
- New feature: FPP hub stiffnes is included into default stiffness of TVC FEM element
- New feature: element mass may be turned off in vibrations
- New feature: drop down report selection in the Report window
- New feature: vibration results view synchronization between all states
- New feature: real node RPM is also mentioned in Time Waveform graphs
- New feature: propeller law degree (2 by default)
- New feature: jack factor calculation settings
- New feature: jack load graph included in shaft alignment report if jack factor calculation is set to Simulation
- New feature: half coupling default center of gravity
- New feature: half coupling gravity center is displayed in Torsional application Inspector
- New feature: Deviation graph added to Reverse Alignment calculation report
- New feature: technical GAP in couplings
- New feature: Wakeflow and Improved Wakeflow methods tables copy/paste
- Update: rolling bearing can be used as a gear bearing
- Update: tables numbers in the Report
- Update: significant orders are applied to the Time wave forms
- Update: significant orders improvements
- Update: jack up test simulation improvements
- Update: Campbell diagram improvements
- Update: Bureau Veritas class 1C
- Update: TVC diesel excitation review
- Update: sample projects
- Update: projects backup
- Update: flanges and half couplings FEM model conversion
- Update: both real and imagine gas excitation table can be used
- Update: removed limitation of the next to the flange element's diameter
- Update: whirling advanced natural frequencies calculation improved
- Update: strain gauges calculation charts visual improvements
- Update: CPP weight in water
- Update: Excluded from calculation list is always visible in options
- Update: the warning is shown instead of zero ice impact torque if the Class requirements are violated
- Update: Ice impact calculation rules updated
- Update: Ice impact torque calculation updated
- Update: OpenBLAS is updated to the latest version
- Update: different flanges diameters SAG&GAP reporting
- Update: torsional natural frequencies calculation and reports
- Update: rigid elements removed from ice impact analysis
- Update: software start up logs
- Update: Improved wakeflow method's database axial coefficients for two-screw ships
- Update: Improved wakeflow velocity field calculation
- Update: harmonic response calculation with different harmonics set per RPMs
- Update: TVC element properties window improvements
- Update: harmonic response results analysis window improvements
- Update: rigid elements removed from harmonic response results analysis
- Update: engine properties window optimized
- Update: engine's excitation report shows only enabled orders
- Update: MS Visual C++ runtime library is not supplied anymore
- Update: TVC scheme inertia drawing improved
- Update: reverse calculation input window improved
- Update: dominating orders calculation
- Update: misalignment calculation improved
- Update: DNV GL lubrication criteria
- Update: calculation results with hidden excitation orders
- Update: converting elements into flanges in Modeler
- Update: whirling advanced calculation improved
- Update: setting half coupling gravity center point
- Update: reverse calculation improved
- Update: including misfiring orders into orders list in calculation options
- Update: RPMs list to calculate in vibrations
- Bug fix: spectrum diagram
- Bug fix: materials numbers in the Report
- Bug fix: jack up test simulation and estimation
- Bug fix: half-coupling selection
- Bug fix: propeller's entrained water calculation
- Bug fix: impeller conversion to TVC scheme
- Bug fix: bush wear and estimated jack correction factor
- Bug fix: renaming state not saved
- Bug fix: TVC calculation speed range
- Bug fix: half coupling center of gravity calculation
- Bug fix: gear box flange loads estimation
- Bug fix: AOD settings
- Bug fix: context menu if project's window is not arranged 'Tabbed'
- Bug fix: masses of the flanges and half couplings synchronization between Modeler and applications
- Bug fix: electric motor excitation display
- Bug fix: 'Print bolt information' report setting
- Bug fix: selected orders generates 'Out of range' error in misfiring calculation
- Bug fix: adding a shaftline aft to gear box
- Bug fix: default HD loads point of the propeller
- Bug fix: entering center point of propeller is not updating Inspector
- Bug fix: moving projects in Project Manager
- Bug fix: flange polar inertia is not displayed in Torsional application Inspector
- Bug fix: disabled damping is shown as active in TVC elements table
- Bug fix: element vibratory torque acceptance criterion continues value
- Bug fix: FPP placing
- Bug fix: internal stern tube coupling position
- Bug fix: ice impact calculation 'Out of range' error
- Bug fix: 'Access violation' error in vibrtion calculation if no element with diameter is introduced
- Bug fix: blade rake angle saving/loading
- Bug fix: opening project file if the turning wheel was selected when saving
- Bug fix: hybrid installation TVC excitation
- Bug fix: electric motor excitation checkboxes
- Bug fix: decoupling flanges coupling with spacer ring
- Bug fix: alignment calculation if jack is set to the middle of the gear wheel
- Bug fix: reverse calculation report
- Bug fix: Decouple&shift calculation report
- Bug fix: SAG&GAP tolerance diagrams
- Bug fix: TVC scheme nodes copy/paste
- Bug fix: significant orders in time waveforms
- Bug fix: propeller HD loads eccentricity default calculation
- Bug fix: time waveforms orders names
- Bug fix: malfunction's barred zones
- Bug fix: Damping Geislinger coupling